Why MAWP i.e. maximum allowable working pressure is significant in pressure safety valve design however usually not illustrate on name plate of vessel?

Forward me your mail id in comment section to download editable spreadsheet. 
Or 
Mail me on "harshalthakar@gmail.com" and I will reply with spreadsheet. 





Comments

  1. Anonymous9 January 2023 at 03:35

    Chemengseliem@yahoo.com, thanks in advance

    ReplyDelete
  2. Anonymous10 January 2023 at 12:58

    pawaramol19@yahoo.com

    ReplyDelete
  3. Anonymous21 January 2023 at 17:04

    hardik.lunagariya0807@gmail.com

    ReplyDelete
  4. Virendra Shinde23 January 2023 at 14:24

    virendra7510@gmail.com

    ReplyDelete
  5. Anonymous28 January 2023 at 05:31

    nanduapna94@gmail.com

    ReplyDelete
  6. amir4 June 2023 at 22:15

    amirabaza@gmail.com

    ReplyDelete
  7. Anonymous28 December 2023 at 19:58

    veerthakurkk@gmail.com

    ReplyDelete

Post a Comment

Popular posts from this blog

What is dry bulb and wet bulb temperate 🌡️?

Dry Bulb Temperature:👇  Definition: Dry Bulb Temperature: This is the temperature of the air measured by a standard thermometer without considering moisture content.   Wet Bulb Temperature: This is the temperature recorded by a thermometer whose bulb is covered with a wetted wick, representing the lowest temperature air can reach through evaporative cooling.   Measurement Method: Dry Bulb Temperature: It's measured using a regular thermometer exposed to the air. Wet Bulb Temperature: It's measured using a thermometer with a wetted wick exposed to the air.   Relation to Humidity: Dry Bulb Temperature: It's unaffected by humidity levels. Wet Bulb Temperature: It's influenced by humidity; higher humidity reduces the rate of evaporation, resulting in a higher wet bulb temperature compared to drier conditions.   Indication of Moisture Content: Dry Bulb Temperature: It doesn't directly indicate moisture content. Wet Bulb Temperature: It indirec...
Read more

What is dead-heading a pump?

A dead-head is caused when a centrifugal pump operates with no flow through the pump due to a closed discharge valve or blockage in the line. The pump is forced to circulate the pumped medium, causing the temperature to continually rise. As the fluid churns inside the pump it heats into a vapor. Once a vapor is created, any bushings or mechanical seals in the pump heat to the point that they begin to crack, shatter, score or compromise the elastomers - killing the pump. When a centrifugal pump is dead-heading, it can lead to explosions, due to the energy being put into the liquid in the pump. Hydraulic overpressure and possible chemical reactions in the pump can also be caused by the overexertion of pressure. The same results can be caused by running the pump dry for an extended period - which can lead to cavitation.
Read more

What is Hoop stress (Circumferential stress) and longitudinal stress in pressure vessels?

Image
  It all starts from fabrication of pressure vessel. Let me explain you. Consider a cylindrical pressure vessel which has been fabricated as per the your requirement. (see below figure) When you fabricate any vessel, you need some plates, pipes, etc. Not everything is ready made.  Post this, you need to weld plates and pipes na!  There are many layers of sheets of stainless steel or metal. When this vessel is subjected to internal pressure, stress observed at different places/ points. Let us cut down this cylinder perpendicular to its axis. See following image. “Circumferential (hoop) stress is due to longitudinal weld and Longitudinal stress is due to circumferential weld.” If we need to calculate this stresses applied to cylinder, we need equation for this. Let us see how we can create equation. Hoop stress:  This stress is due to longitudinal weld. It proportional on internal pressure and internal diameter of vessel. When both increases, stress increases. It inver...
Read more